(Jul. 25, 2018  4:44 PM)Thunder Blur Wrote:

(Jul. 25, 2018  4:16 PM)CitrusNinja3 Wrote: Has anyone tested these out? O2 is my favorite Dual Layer, and this design makes it even cooler!

It literally came out last night

(Jun. 28, 2018  8:40 AM)CrazyAries Wrote: This is not only a custom Layer.
This is totally a new Beyblade!
For one of the impressive beyblade of Metal series, I made a Burst version!
Earth Aquila. E. K!

Layer-Earth Aquila

Spoiler (Click to View)

Disc-End

Spoiler (Click to View)

Driver-Kernel

Spoiler (Click to View)

Video

Spoiler (Click to View)

Download files

(Jul. 25, 2018  4:16 PM)CitrusNinja3 Wrote: Has anyone tested these out? O2 is my favorite Dual Layer, and this design makes it even cooler!

(Jul. 25, 2018  5:58 PM)LOL-y Rancher Wrote: Are there any other Cho-Z remakes you're planning to do? Like a Zeus or a Spriggan?

FYI, not trying to pester you. I'm just curious about your future plans haha.

(Jul. 25, 2018  9:59 PM)Thunder Blur Wrote:

(Jul. 25, 2018  5:58 PM)LOL-y Rancher Wrote: Are there any other Cho-Z remakes you're planning to do? Like a Zeus or a Spriggan?

FYI, not trying to pester you. I'm just curious about your future plans haha.

I have someone making X spriggan based on your design ^^

(Jul. 25, 2018  5:23 PM)CrazyAries Wrote:

(Jul. 25, 2018  4:16 PM)CitrusNinja3 Wrote: Has anyone tested these out? O2 is my favorite Dual Layer, and this design makes it even cooler!

It is so heavy now so that is very good at performance... But I don't think this is too early to say it is good. I will make another one that is totally plastic, to see how it really works.

(Jul. 28, 2018  9:26 PM)Beyblade Beyond Wrote: If it's not too much to ask, what site or service did you use to 3D print the parts for Cosmic Odin's layer?

Spoiler (Click to View)

This design is similar to Z2 and gZ, that use metal balls in the layer. (Jupiter and Zeus are basically the same god but different name in different culture)
What is different is that the metal balls in this layer is much larger so that they should be more effective, and they are exposed so that can directly hit opponents to improve both attack and defense.
Cho Z Ability: Satellite Zone
Type: Balance


There are two main parts and some metal balls for this layer. For the two main parts, the files zj1 and zj2 will be needed. You can directly 3D print both parts, and if you like, you could make them different material. That's up to you (But I don't suggested you to make them metal, since that could make this beyblade too heavy and may damage your launcher).
There are two sizes of metal balls on this layer, that one is 8mm in diameter and one is 6mm. 2 of 8mm balls are needed, and the amount of 6mm could vary as you like. 
There are the files of those two metal balls, but I suggest you to directly purchase them since that would be much cheaper.
4 M2*5 screws will be needed (or you can get them from any official release).

Spoiler (Click to View)

You will need a Magnum, Jerk or Polish, and get the metal part from them for this disc. you could 3D print this part and I suggest you to use rubber. You can then assemble this part with the metal part you get from disc M/J/P

Spoiler (Click to View)

This Driver is a combination of Bearing and βite.
The white ball tip is made of rubber, so it can better catch the stadium and will not be easily knocked off the stadium.
Its bearing inside could improve its stamina (as you know, rubber tips has horrible stamina due to the friction, but the bearings could help).
And it is very tall. It's significantly higher than Volcanic and the burst bey with this driver could be as tall as the 230WD combos in metal series.


There are 4 files to make this driver. The tip(Quell4) is supposed to be Rubber but you can make it plastic or any material you like. You will need a M2*6 screw, two 4*7*2.5 bearings and a M2*5*0.3 gasket to assemble it.
You need to get the white ring and the spring from another driver. (Warning: This may totally destroy that driver.)
Also, you would need another two M2*8 screws to finally complete this driver.

(Jul. 30, 2018  5:18 AM)CrazyAries Wrote: Here is a new custom bey. It's called Zone Jupiter. Zigzag. Quell. (zJ.Z.Ql)
It's perhaps the last custom beyblade this summer break. I almost used up all my money (the metal workshop is really expensive...) and I need to prepare for the new semester.

Layer - Zone Jupiter (zJ)

Spoiler (Click to View)

This design is similar to Z2 and gZ, that use metal balls in the layer. (Jupiter and Zeus are basically the same god but different name in different culture)
What is different is that the metal balls in this layer is much larger so that they should be more effective, and they are exposed so that can directly hit opponents to improve both attack and defense.
Cho Z Ability: Satellite Zone
Type: Balance


There are two main parts and some metal balls for this layer. For the two main parts, the files zj1 and zj2 will be needed. You can directly 3D print both parts, and if you like, you could make them different material. That's up to you (But I don't suggested you to make them metal, since that could make this beyblade too heavy and may damage your launcher).
There are two sizes of metal balls on this layer, that one is 8mm in diameter and one is 6mm. 2 of 8mm balls are needed, and the amount of 6mm could vary as you like. 
There are the files of those two metal balls, but I suggest you to directly purchase them since that would be much cheaper.
4 M2*5 screws will be needed (or you can get them from any official release).

================================================================================

Disc - Zigzag (Z)

Spoiler (Click to View)

You will need a Magnum, Jerk or Polish, and get the metal part from them for this disc. you could 3D print this part and I suggest you to use rubber. You can then assemble this part with the metal part you get from disc M/J/P

================================================================================

Driver - Quell (Ql)

Spoiler (Click to View)

This Driver is a combination of Bearing and βite.
The white ball tip is made of rubber, so it can better catch the stadium and will not be easily knocked off the stadium.
Its bearing inside could improve its stamina (as you know, rubber tips has horrible stamina due to the friction, but the bearings could help).
And it is very tall. It's significantly higher than Volcanic and the burst bey with this driver could be as tall as the 230WD combos in metal series.


There are 4 files to make this driver. The tip(Quell4) is supposed to be Rubber but you can make it plastic or any material you like. You will need a M2*6 screw, two 4*7*2.5 bearings and a M2*5*0.3 gasket to assemble it.
You need to get the white ring and the spring from another driver. (Warning: This may totally destroy that driver.)
Also, you would need another two M2*8 screws to finally complete this driver.

================================================================================

Video

Spoiler (Click to View)

Download

(Jul. 30, 2018  5:30 AM)Beyblade Beyond Wrote: Nice, you completed it and as expected it's a work of art as always with impressive performance and engineering, good job also hope everything goes well for you with the new semester around the corner.

Also just out of curiousity, what paint do you use? Because I'm guessing it's pretty resistant in terms of when your just carrying it around and what not.

(Jul. 30, 2018  6:57 AM)CrazyAries Wrote:

(Jul. 30, 2018  5:30 AM)Beyblade Beyond Wrote: Nice, you completed it and as expected it's a work of art as always with impressive performance and engineering, good job also hope everything goes well for you with the new semester around the corner.

Also just out of curiousity, what paint do you use? Because I'm guessing it's pretty resistant in terms of when your just carrying it around and what not.

I used the paint of Tamiya. But it may not be so resistant as you expected.

Spoiler (Click to View)

One thing that may disapoint you is that I didn't add the function of mode change on this layer. I think Assault mode is the one that people usually use so I just make it in Assault mode.

Spoiler (Click to View)

The red tip is rubber. This Driver is basically a Burst format of RSF.
Also, In order to realize the feature of Track 100, I made this driver short. So the bey would be good at Upper attack, but you need to be careful as the disc may touch the stadium.

(Aug. 01, 2018  5:52 AM)CrazyAries Wrote: I've complete the 3D model of Blitz Unicorno in Burst format. But I haven't make it real because I used too much money on previous beys and now I don't have enough money...
I prepared a Layer and a Driver for Blitz Unicorno and I think Disc Triple will be a good choice so I didn't design the disc (Ans I think I have already complete the Alphabet for Disc...)

Layer - Blitz Unicorno (bU)

Spoiler (Click to View)

One thing that may disapoint you is that I didn't add the function of mode change on this layer. I think Assault mode is the one that people usually use so I just make it in Assault mode.

Driver - Dive (Dv)

Spoiler (Click to View)

The red tip is rubber. This Driver is basically a Burst format of RSF.
Also, In order to realize the feature of Track 100, I made this driver short. So the bey would be good at Upper attack, but you need to be careful as the disc may touch the stadium.

File Download

(Aug. 08, 2018  12:50 PM)WolkaiserDrake Wrote: managed to make it even with a bit of fiddling, and math
https://sta.sh/01ckh8tnx6pm

(Aug. 08, 2018  8:02 PM)BlackMirror Wrote:

(Aug. 08, 2018  12:50 PM)WolkaiserDrake Wrote: managed to make it even with a bit of fiddling, and math
https://sta.sh/01ckh8tnx6pm

You could PM Xandork about this idea. The requirements and price are on his thread: https://worldbeyblade.org/Thread-Cho-X-Custom-3D-Beys. He makes custom beys, so maybe he could make the bey that you designed too.